Low Voltage Electrical Equipment & Supplies Power Distribution Board and Switchgear Type Distribution Box

• Customization: Available
• Type: Power Transmission and Distribution
• Structure: Open Frame
• Certification: ISO9001:2000, CCC
• Form: All- packaged Type
• Operation Voltage: Low Voltage
• Size: 1 Uint
• Application Range: High-rise Buildings
• Shell Material: Customization
• Shell Protection Grade: Customization
• Brand: Guang Bian
• Rated Frequency: 50Hz/60Hz
• Protection Level: IP20/IP30/IP40
• Voltage: 380V
• Nominal Voltage: 380V
• Rated Current: 400~3200A
• Current: 400~3200A
• Transport Package: Wooden Case Packing
• Trademark: Guang Bian
• Origin: Zhejiang, China
• HS Code: 853710909
• Production Capacity: 5000 Set/Sets Per Year
• Package Size: 1.00cm * 1.00cm * 1.00cm
• Package Gross Weight: 1.000kg

Product Description

 

 

Product Description

Switchgear,also known as low-voltage AC distribution cabinet,alsoLow voltage distribution panel.

The low-voltage distribution panel produced by our company is a new type of distribution cabinet that has been redefined and designed according to international electrical technology standards.
*They comply with the GB7251 and LEC60439 standards.

It is widely applicable in various scenarios such as indoor areas (such as squares, communities), substations, power plants, industrial enterprises, etc.

We can flexibly match low-voltage components in the low-voltage distribution panel according to customer needs. For example, based on your country's frequency (50/60HZ), voltage (380V/400V, etc.), and the rated current required for actual scenarios (630A~3150A, etc.), configure the power, lighting, and distribution equipment needed for your power distribution system for power conversion, distribution, and control.

 

DIY Your Switchboard

*Our customization doesn't stop there. We'll draw on our 20 years of experience. According to your drawings, according to your actual situation, to help you develop a better electricity plan

** Components in the cabinet can be replaced according to customer requirements.

Frame type circuit breaker:
Can be switched on, carry and break the current under normal circuit conditions, can also be switched on under specified non-normal circuit conditions, carry a certain time and break the current of a mechanical switch.
 

Circuit breaker:

Similar to the function of the frame circuit breaker, mainly to protect the various lines.

Current transformer:

It is an instrument that converts the large current on the primary side into the small current on the secondary side according to the principle of electromagnetic induction. The current transformer consists of a closed core and winding.

Voltage transformer:

Voltage transformer for the purpose of transforming voltage, mainly used to supply power to measuring instruments and relay protection devices.

Fuse:

When the current exceeds the specified value, the heat generated by itself fuses the melt and breaks the circuit.

Knife switch:

also known as the knife, is generally used for AC and DC low circuits that do not need to be cut off and closed frequently, and its working current cannot exceed the rated value at rated voltage.

pilot lamp
voltmeter
ammeter
change-over switch
 

You can choose your low voltage cabinet configuration as you would a house

(↓Contact me on Chat.)  

 

 

Use environment advice

 

1.Ambient air temperature not higher than + 40 ° C and not lower than -5 ° C. The average temperature shall not be higher than +35° C within 24 hours. In case of exceeding, the capacity shall be reduced according to the actual situation.
 

2.For indoor use,the altitude of the place of use shall not exceed 2000 meters.
 

3.The relative humidity of ambient air shall not exceed 50% at the maximum temperature of + 40 ° C, and a higher relative humidity is allowed at a lower temperature: for example, 90% at + 20 ° C.The influence of occasional condensation due to temperature change shall be taken into account.
 

4.When the device is installed,the inclination to the vertical plane shall not exceed 5 °, and the whole cabinet array shall be relatively flat.
 

5.The device shall be installed in a place where there is no severe vibration and impact, and the device is not enough to cause undue corrosion of electrical components.

 

 

Why Choose Us

Four production workshops

Our company's four workshops can achieve diversified production of transformer products. And achieve high-fit assembly and testing to ensure the high efficiency and safety of each transformer.
Due to the independent control of all aspects of our company, we can achieve economic benefits for our products. We ensure that each product is not only of high quality, but also very cheap.
 

Industry standard production equipment

Authentication Certificate

 

 

Shipping And Packing

 

 

FAQ

Q: Are you a manufacturer or trading company?

A: We are a professional factory

 

Q: How long have you been worked in the electric industry?

A: 2024 is exactly the 20th year of our company.

 

Q: How long is the warranty period?

A: We offer 12 months warranty time.

 

Q: Would you accept using customer's logo?

A: Yes, we can provide OEM and ODM service.

 

Q: What's the MOQ?

A: It is 1 set.

 

Q: What's the payment terms?

A: We accept T/T, L/C,Western Union, PayPal, etc.

 

Q: How long is the delivery time?

A: 15 to 45 days or depending on order requirements.

 

Q: What is the standard of package?

A: Export standard package or special package according to customer's requirement.

 

Q: How do you conduct quality control in your factory?

A: We have a professional product testing room, and we will carry out factory testing on every product. Only 100% qualified products can leave our factory

 

Q: Do you have the products in stock?

A: Normally no. All our products produce depending to your order quantity.

 

Q: How can I trust you ?

A: We have been established for 20 years and have ISO9001 certificates and various type test reports. Our products are widely used all over the world. We believe that we can provide you with high quality products at competitive prices. And we are an audited supplier of diamonds made in China.

 

Q: What should provide to make custom transformer ?

A: Technical drawing and technical specification document are the best, or you can tell us some details technical specification date as below "Quotation and Ordering Required Information".

 

Q: Could I have your catalog and price list for trial order in MOQ quantity?

A: All of our products are showing on Made-in-China or official website, you are always welcome to ask us to get more information directly.